Hapi - computer PMX build

[draudio2u]

I know this should probably fall under "Hardware" but figure this is where I would receive the most response in regards to how people are building their systems if you haven't purchased a turnkey system from Merging.
Below I paste my computer current configuration and have had minimal problems using it with Mytek converters via their USB drivers. I just purchased a HAPI in order to open up the Masscore side and work in DSD/DXD. I am having extreme problems with Ravenna and stabilization. Merging is stating it could be a an issue with Intel Xeon Processor, which is odd because when I purchased this computer just under a year ago, I first sent the build to merging to be sure something like this would not happen - their reply was "It looks like it will work but we have not tested such a configuration". Anyone build a system using the following configuration? It is a Dell Precision R7610 rack frame

Thank you in advance:


System summary


Computer Model
Precision R7610
!210-AAPM : Dell Precision R7610 CTO Base

T845M

!370-AATO : 16GB (4x4GB) 1866MHz DDR3 ECC RDIMM

7826W

4

DUAL IN-LINE MEMORY MODULE, 4GB, 1866, 1RX8, 4G, DDR3, R

!490-BBFY : DUAL 512MB AMD FirePro 2270 (2 cards w/ DMS59) (2DMS59 to 2D VI adapter)


H9361

2
JCPR7

2

CARD (CIRCUIT), GRAPHICS, 512MB, MV2270, V2

!400-ACXQ : 256GB 2.5inch Serial ATA Solid State Drive

3R81M

1

ASSEMBLY, CARRIER, HARD DRIVE, R5500

YRK2P
1
SSDR, 256G, S3, 7MM, SAMSUNG, SM841N
FM833

1R9445
!429-AAFM : 6x Slimline Blu-ray Writer
ASSEMBLY, Blu-ray Rewritable, 6X, 12.7T, PANASONIC, ACROSS LINE OF BUSINESS


!338-BBYN : Intel Xeon Processor E5-2609 ( Quad Core, 2.40GHz, 10MB, 6.4 GT/s)
6C25F
1
Processor, E52609, 2.4, 10M, SNB, 80W, M1 Video Cable

!401-AAHO : 600GB 2.5inch SAS (10,000 Rpm) Hard Drive

3R81M
ASSEMBLY, CARRIER, HARD DRIVE, R5500
5TFDD
HARD DRIVE, 600G, SERIAL ATTACHED SCSI, 10K, 2.5, T-13SE, E/C
ASSEMBLY, CARRIER, MOUNTING, BLANK , HARD DRIVE, 2.5, V3

Label, Certificate Of Authenticity, Operating System, W7P3/6

!631-AAAV : Intel vPro Technology Enabled
!330-BBBE : Center riser with (1) PCIe x16 and (1) PCIe x16, wired as x8 (requires 2nd CPU to enable P CIe slots)


PRINTED WIRING ASSY, RISER, INPUT/OUTPUT, PRECISION WORKSTATION, R7610, OPT1
!329-BBIP : Dell Precision R7610 TPM Chass is

[robertopisa]

I cannot understand if you have an inboard NIC for Ethernet or if you are using the one sold by Merging.
I do not use Masscore on my Hapi, so I have installed a PCIe Intel Pro dual port of top quality (server edition).
Also, if you use a switch, check if it is compatible.
-R

[DJS]

Hi Robert, I use Native like you. I have one NIC dedicated to Ravenna (set to auto IP) and it connects directly to Horus/Hapi. The other NIC (set to DHCP) goes to my studio switch where it connects to PMX-ISIS controller, NAS drives, printer, broadband router etc. This works without issue.